Temperature Mapping of Warehouses and Stability Chambers

Last reviewed 12 Nov 2026 · 9 min read

Contents
  1. What a mapping study can show
  2. Warehouse and chamber studies have different purposes
  3. Plan the study before placing loggers
  4. Seasonal and change considerations
  5. Mapping protocol and report template
  6. Common mistakes
  7. Fictional example
  8. Frequently asked questions
  9. Is warehouse mapping the same as stability-chamber mapping?
  10. How often should a warehouse be remapped?
  11. How many loggers should a study use?
  12. What should happen after an excursion?
  13. Related reading
  14. References

In short: Temperature mapping shows how temperature varies across a warehouse or chamber under defined operating conditions. It helps teams identify hot and cold locations, choose routine monitoring points and assess whether the intended storage environment is suitable. Warehouse guidance and stability-study requirements have different scopes, so use the right protocol and do not copy a warehouse mapping rule into a chamber qualification without a documented rationale.

What a mapping study can show

A map is a set of measurements from multiple locations across a defined space and operating period. It can reveal temperature gradients, local hot or cold zones, airflow issues and the effect of loading or operations. The report can help the site decide where products may be stored and where routine sensors should be placed.

Mapping is different from continuous monitoring. Monitoring follows selected points after the space has been qualified; mapping helps justify those points and examine whether other parts of the space behave differently. A single room sensor can miss a local variation, particularly in a high-bay store or a densely loaded chamber.

The scope of this article is a study plan and report workflow. It does not set universal acceptance limits, logger counts, study durations or re-mapping frequencies. Those decisions belong in the approved protocol and depend on the temperature range, space design, load, product requirements and risk assessment.

Warehouse and chamber studies have different purposes

TopicTemperature-controlled warehouse or storeStability chamber
Primary questionAre product storage locations within their approved storage ranges during normal use?Are samples held at the conditions specified by the stability protocol?
Main operating variablesDoor openings, seasonal heat, loading patterns, airflow and equipment cyclingShelf and chamber position, sample load, chamber recovery, sensors and alarms
Useful mapping outcomeHot/cold zones, unsuitable racks or shelves and representative routine-sensor locationsEvidence that study samples experience the intended chamber conditions, plus defined response to excursions
Relevant guidanceWHO TRS 961 Annex 9, Supplement 8, published in WHO TRS 992 Annex 5 (2015)ICH Q1A(R2), EU GMP Annex 15 and applicable stability procedures

WHO’s temperature-mapping supplement addresses temperature-controlled storage areas for temperature-sensitive products. It discusses mapping protocols, logger selection, data review, seasonal effects, high-bay temperature stratification and recommendations for storage zones. It is useful for warehouse studies; it does not provide a stability-chamber qualification protocol.

For stability chambers, ICH Q1A(R2) (2003) describes stability-study conditions and says equipment should control the storage condition within the guideline’s ranges, with actual temperature and humidity monitored where controlled. It also says excursions beyond defined tolerances for more than 24 hours should be described in the study report and their effect assessed. ICH is revising its stability guidelines into a consolidated Q1 guideline; check the ICH website for its current status, and use the applicable final guideline and regional requirements until a revised version is adopted.

EU GMP Annex 15 (2015) provides lifecycle and risk-based principles for qualification and validation of facilities, equipment and utilities. In the United States, 21 CFR 211.166 requires a written stability-testing program that includes sample storage conditions and uses results to determine appropriate storage conditions and expiration dates. Neither reference supplies a universal map layout or a single study duration for every chamber.

Plan the study before placing loggers

  1. Define the scope and objective. Identify the room or chamber, its use, operating range, products or study samples, normal load and the decision the study must support. State whether the exercise is initial qualification, a change assessment, a seasonal check or an investigation.
  2. Review the design and risk. Examine room dimensions, ceiling height, racking, air supply and return, doors, heaters, cooling coils, work areas and locations where products can be placed. For a chamber, review shelves, fans, sensors, control probes, alarms and the planned sample arrangement.
  3. Specify operating conditions. Describe empty or loaded conditions, normal traffic, door openings, representative sample load, equipment settings and relevant seasonal conditions. Use the product label or stability protocol as the basis for the temperature range. Do not replace the approved study condition with a generic “room temperature” value.
  4. Prepare and approve a protocol. WHO TRS 992 Annex 5 Supplement 8 calls for a detailed mapping protocol to be prepared, reviewed and approved before the study. Include rationale, scope, objectives, method, logger locations, data analysis, acceptance approach, reporting format, deviations and approvals.
  5. Select suitable instruments. Choose calibrated loggers with a range and memory suitable for the planned study. The WHO supplement’s logger guidance for storage-area mapping describes a programmable sampling period in the range of 1 to 15 minutes and a NIST-traceable three-point calibration with a stated error no greater than ±0.5 °C at each calibration point. Assess separately whether those recommendations fit a specific chamber study, instrument design and applicable requirements.
  6. Set locations to answer the protocol question. Cover the usable space and expected variation, not only convenient locations. WHO specifically notes that high-bay pallet-rack stores are susceptible to stratification and should be mapped over their full working height. In a chamber, place sensors to assess spatial differences across shelves and near relevant air paths without obstructing normal operation.
  7. Run the study under defined conditions. Install and identify loggers, synchronise clocks, document start and stop, and preserve the operating log. Note door events, alarms, power interruptions, maintenance and deviations that could explain a temperature change.
  8. Review data and make a disposition. Check for missing data, logger faults and unusual spikes before calculating summaries. Review maximum, minimum and location-specific patterns against the approved criteria. A good average does not make a local excursion disappear.
  9. Map findings to routine use. Document suitable and unsuitable zones, sensor locations, product-loading or sample-placement controls, and any remedial action. If results do not meet the approved study criteria, follow the deviation process and assess product or study-sample impact before use or continued reliance on the space.

Seasonal and change considerations

For storage areas affected by seasonal temperature variation, WHO states that at least two mapping studies may be needed, typically during the warmest and coldest seasons. It also notes that two-season mapping is typically not necessary for cold rooms and freezer rooms. These are WHO recommendations for temperature-controlled storage areas; do not automatically apply them to stability chambers without a protocol rationale.

Reassess the mapped state when a change could affect airflow, loading or temperature control. Examples include changed racking or sample placement, HVAC or refrigeration work, a changed control setting, repeated unexplained temperature variation, or an alarm or excursion investigation. Annex 15’s lifecycle approach expects planned changes that may affect product quality to be documented and their impact on validated status or control strategy assessed.

Mapping protocol and report template

Use this blank outline as a starting point. It is not a pre-approved form or a set of universal acceptance criteria.

SectionInformation to define or record
Space and purposeWarehouse zone or chamber ID, intended use and study objective
Applicable conditionsProduct label or approved stability-protocol range and source
ConfigurationEmpty/loaded state, rack or shelf arrangement and operating conditions
Instrument detailsLogger IDs, calibration status, range, sampling settings and clock check
Location planMap, location IDs, height or shelf, and reason for each position
Study executionStart/stop, operator, operating events, alarms and deviations
Data reviewMissing-data checks, temperature plots, maxima/minima and spatial patterns
FindingsHot/cold zones, suitability decision and product/sample impact assessment
ActionsSensor placement, loading controls, repairs, follow-up and change-control reference
ApprovalAuthor, reviewer, quality approval and report date

For product-batch documentation, retain records at least one year after expiry of the respective product batch. EU GMP Volume 4 Chapter 4 §4.11 specifies the longer of one year after expiry or five years after Qualified Person certification for batch documentation; 21 CFR 211.180(a) sets at least one year after expiry for applicable US drug-product records. Follow any longer applicable retention requirement.

Common mistakes

  • Using too few locations to represent the space: A convenient sensor position may not reveal vertical or local variation. Justify coverage in the protocol.
  • Mapping only an empty room: Empty-space data may not describe airflow under a representative load. Define which configurations answer the risk question.
  • Reporting only an average: Maximum, minimum and spatial trends can reveal a zone that is unsuitable even when the overall average looks acceptable.
  • Treating WHO warehouse guidance as chamber law: The WHO supplement is written for storage areas. Apply chamber study conditions from the approved stability protocol and relevant qualification system.
  • Using logger values without calibration review: A mapping result is only as useful as the measurement system. Check calibration, identification, clock synchronisation and data integrity.
  • Ignoring study excursions: An excursion can affect the stability data even if the chamber later returns to its set point. Document and assess it using the current stability procedure.
  • Setting re-mapping intervals by habit: Define reassessment based on risk, data trends, changes and the approved site programme rather than copying an unsupported fixed interval.

Fictional example

A site maps a high-bay warehouse after installing a new rack layout. The approved protocol includes locations across the usable height and representative operating conditions. The results show a recurring warm zone near an air supply and a colder pattern near another location. The report identifies where product can be stored, where it should not be placed and which routine sensor positions best reflect the qualified space. A separate stability chamber study uses the chamber’s approved sample arrangement and stability protocol; the warehouse logger layout is not copied automatically.

Frequently asked questions

Is warehouse mapping the same as stability-chamber mapping?

No. Warehouse mapping addresses storage-area variation during operational use. A stability chamber must maintain the conditions in the applicable stability protocol and be managed within the facility’s qualification and change-control system. The objectives and protocols should be clear for each space.

How often should a warehouse be remapped?

The cited WHO supplement does not set one interval for every facility. It says periodic re-mapping may be required depending on the routine monitoring strategy, giving every three years only as an example, and that mapping should also follow significant modifications to the store. Use the approved site programme, risk assessment, monitoring trends, seasonal conditions and changes that could affect the mapped state.

How many loggers should a study use?

Choose enough locations to represent the space and answer the study objective. WHO’s supplement gives design guidance for storage areas, including full-height coverage in high-bay stores; it does not establish one logger count for every room or chamber.

What should happen after an excursion?

Record the event, assess the affected product or stability samples against the approved procedure, and document any impact on the study or storage decision. ICH Q1A(R2) says excursions exceeding defined tolerances for more than 24 hours should be described in the study report and their effect assessed.

References

Related articles